Aqua Lung SEA MK Instrukcja Użytkownika

Survival Egress Air(SEA)User's ManualLV2MKRev. 12/10

10 SEA USER'S MANUALWARNING: DO NOT attempt to ll the SEA from a supply cylinder which contains more than 3,100 PSI / 214 BAR. Doing so may we

11SEA USER'S MANUAL8. When at least two minutes have elapsed, and air can no longer be heard owing from the supply cylinder into the SEA, turn

12 SEA USER'S MANUALNOTE: The Compressor Fill Adapter (P/N 100656) is not included with SEA and must be purchased separately.CAUTION: Do not at

13SEA USER'S MANUALWARNING: DO NOT attempt to ll the SEA from a compressor or air supply where the regulated pres- sure exceeds 3,000 PSI / 20

14 SEA USER'S MANUALFilling the SEA with the MRS-III Mobile Rell Station7. To conserve the limited air supply of the SEA, it is strongly recom-

15SEA USER'S MANUALNOTE: If the SEA cylinder becomes excessively warm to the touch while lling, allow additional lling time for the unit to co

16 SEA USER'S MANUAL10. To conserve the limited air supply of the SEA, it is strongly recom-mended that you perform the following pre-issue insp

17SEA USER'S MANUALHexagonal Mouthpiece BossHexagonal shaped mouthpiece and mouthpiece boss allows for multiple positionsHexagonal MouthpieceAdj

18 SEA USER'S MANUALChanging Position of mouthpiece1. Mount SEA bottle in user preferred position.2. Using side cutters, remove the mouthpiece

19SEA USER'S MANUALNOTE: Part Number 108382 and 108485 do not have an on/off valve; therefore, the pressure indicator gauge and second stage are

2 SEA USER'S MANUALA WARNING indicates a procedure or situation that, if not avoided, could result in serious injury or death to the user.A NOTE

20 SEA USER'S MANUALNOTE: If the second stage purge was checked during the lling procedure, it is not necessary to repeat steps 7 & 8.5.

21SEA USER'S MANUALThe pre-ight inspection shall be performed on the SEA prior to each ight by the air crew member to whom the unit is assigned

22 SEA USER'S MANUALCare & MaintenanceIt is important to provide the proper preventative maintenance in order to ensure the best possible per

23SEA USER'S MANUALWARNING: DO NOT store the SEA partially lled. Doing so may prevent the safety relief assembly from functioning proper

24 SEA USER'S MANUALWARNING: Do not attempt to loosen or remove the rst stage hose tting, gauge or safety burst plug under any circum-stances.

25SEA USER'S MANUALTechnical SpecicationsCylinder Volume *2.0 cf / 42.5 litersCylinder Material AluminumCylinder Length with Regulator *10.5 in

26 SEA USER'S MANUAL60 ± 5 in.lbs.6.8 ± .5 Nm90 ± 3 in.lbs.10.2 ± .3 Nm90 ± 3 in.lbs.10.2 ± .3 Nm90 ± 3 in.lbs.10.2 ± .3 Nm90 ± 3 in.lbs.10.2 ± .

27SEA USER'S MANUAL ---------108344 Overhaul Parts Kit, 2nd Stage MK/LV2 ---------108315 MK Second Stage Assy, Spare ---------108468 MK Se

28 SEA USER'S MANUALLV2 Second Stage ---------108344 Overhaul Parts Kit. 2nd Stage, MK/LV2 ---------108402 LV2 Second Stage Assy., Spare ---

29SEA USER'S MANUALNOTES

3SEA USER'S MANUALContentsProduct Description ... 4General Precautions & Warnings ...

30 SEA USER'S MANUALNOTES

31SEA USER'S MANUALNOTES

32 SEA USER'S MANUAL©2010 Aqua Lung International2340 Cousteau Court • Vista, CA 92081Phone (760) 597-5000 • Fax (760) 597-4914www.aqualung.com/m

4 SEA USER'S MANUALProduct DescriptionThe SEA MK and SEA LV2 consist of the basic SEA rst stage and cylinder assembly. The products differ in se

5SEA USER'S MANUALGeneral Precautions & WarningsThe SEA is intended for use only as an emergency device to assist a crewmember or passenger i

6 SEA USER'S MANUALComponent IdenticationFirst Stage w/ Integrated ValveCylinderLV2 Second StageSCUBA Fill AdapterMK Second StageNOTE: The aver

7SEA USER'S MANUALMaximum Fill PressureSerial No.Month & Year of ManufactureWARNING: DO NOT attempt to ll the SEA if the cylinder markings

8 SEA USER'S MANUALWARNING: DO NOT attempt to loosen or remove the rst stage hose tting or safety burst plug under any circum-stances. Doing s

9SEA USER'S MANUAL1. Using a calibrated pressure gauge, check the supply cylinder to ensure that it contains at least 2,700 PSI/ 186 BAR and les